Plumbing for Beginners: What You Need for Installing a Bathtub
Plumbing for Beginners: What You Need for Installing a Bathtub
Blog Article
Have you been trying to locate additional info on Installing A Bathtub?
Mounting a tub isn't specifically brain surgery, but it does require solid plumbing, woodworking, and in some cases, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably difficult project. If the old tub is readily easily accessible, the job can relocate quickly; if you have to open a wall to remove the old bathtub and also place the brand-new tub, the task is a lot harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub and also set in the brand-new one. Ensure you have actually certified on your own for the task and also are comfortable trying it. Rather than working with a specialist to take over a halfway-completed project, it is much better to think about employing one prior to you begin. Possibilities are you may require a specialist plumber to make tube connections.
This post will certainly help you set up a brand-new bath tub in your restroom if you have already gotten a brand-new bathtub and also don't need to alter the plan of your previous water pipelines.
Your tools as well as material checklist ought to consist of the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of removing the existing faucets can be quite bothersome as a result of the restricted accessibility that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have been removed, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end provides a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in area between the faucet and also the sink. Protect the faucet in place with the producer given backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The former type must be attached to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The next goal is to make certain that the bathtub is leveled all round. This can be attained by checking the spirit level and adjusting the feet on the bath tub till the level reads degree.
To mount taps, fit all-time low of the furthest versatile faucet port to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system and also examine all joints as well as new pipework for leakages and tighten them if necessary. Fill up the tub and additionally inspect the overflow outlet as well as the regular electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the manufacturer's user's manual. Tiling as well as sealing around the bathtub ought to wait till the tub has actually been utilized a minimum of once as this will certainly settle it into its last position.
Planning for the Installment
Firstly, the sustaining frame supplied with the bathroom must be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is important to ensure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you use all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final position.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, triggering the water to permeate the wall in between the bath as well as the tiling, leading to difficulties with dampness as well as possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to constantly fill up the tub with water before securing, to allow for the movement experienced when the bathtub is in use. The sealer can split relatively early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily readily available on the market. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very inquisitive about Installing A Bathtub and I really hope you enjoyed the blog posting. Liked our article? Please share it. Help another person discover it. Many thanks for taking the time to read it.
Reliable plumber? Dial now! Report this page